CW Laser Power Supply (Lamp Driver)

The STCW series laser power supplies are made for CW lamp-pumped Nd:YAG lasers. The main circuit of the power supply is based on power electronic module IGBT, adopts PWM technique to yield conversion efficiency more than 90%, and outputs constant current with high accuracy and low current ripple. Ignition circuits which produce a high voltage pulse consists of three steps: series high voltage unit for igniting the lamp, LC unit to relay the power, and low –voltage-constant-current to continue the lamp current. Automatic igniting is achieved with igniting-detecting circuit. The successful ratio of one-time ignition is more than 99%. The high voltage rises smoothly, and its magnitude can be adjusted to meet the dispersible characteristics of the krypton lamps, and to reduce the spattering of the electrode material at the same time, and further to reduce the damage to the krypton lamp caused by high voltage triggering. 

The soft-charging circuit and soft-starting circuit are provided to avoid the voltage spiking and in-rush current in the event of starting. Display shows the set current and operation current at different time. The function of “work/sleep” is designed to output normal current at working and low holding current at the time of stand by, so as to increase the efficiency of the power supply, lighten the heat exchanger system, and prolong the lifetime of the lamp as well. Conveniently turns switch to Run/Stop status, adjust output current, and show the working status through the inner/outer control selection.  

Excellent design makes the power supply maintained easily and perfect design of circuit protects the device from over voltage, over current and over heat. 

There are the following advantages of our products:

l         High reliability

l        Advanced design of the whole circuits system highly improves the electrical characteristics of the power supply.

l         Anti-dust design

l         Anti-vibration design

l         Easy maintenance

l         Malfunction indicators

l         Strict testing and 48hour full-load testing in the factory

l         Temperature test in -10℃~70℃ to ensure that it works stably in the ambient temperature at 0℃~50℃.

l         Test in relative humidity 90%.

Measure the current ripple and test the stability of the output current accurately in factory  to make sure that the output current meets the requirements of the Kr lamp.

Part Number Description:

STCWxyzT

STCW –   STCW series CW laser power supplies

X ---------- maximum output current (2 means 20A or 25A, 3 means 30A, 4 means 40A)

Y ---------- Maximum output voltage (4 means 400V, 2 means 200V)

Z ---------  input electricity (A means 3-phase 380VAC, B means 1-phase 220VAC)

T ---------- others

The STCW series digital laser power supplies are made for CW lamp-pumped Nd:YAG lasers. The main circuit of the power supply is based on power electronic module IGBT to yield conversion efficiency more than 95%, and outputs constant current with high accuracy and low current ripple. With the monitor of the trigger process and automatic trigger, the successful ratio of one-time ignition is more than 99%.

There are the following advantages of our products:

• Via micro-computer, automatic control to current setting, logic functions and port communications.

• There are the functions such as trigger delay, lamp-problem interlock, voltage display, error code display, status maintenance etc.

• There are many ports and convenient to connect with computer for remote control.

• 25PIN computer connector for external control and communication. All the digital ports are opto-electronic insulation.

• There are perfect protection functions such as slow-up voltage, slow-start protection, no voltage or low voltage protection, over current protection, over-hot protection, trigger delay protection, lamp-problem protection, external control and error status record etc.

Part Number Description: STCWxyDz

STCW – STCW series CW laser power supplies

X ----------maximum output current (2 means 20A, 3 means 30A, 4 means 40A)

Y ---------- Maximum output voltage (4 means 400V, 2 means 200V)

D --------- digital power supply

Z --------- input electricity (A means 3-phase 380VAC, B means 1-phase 220VAC)